The Cat® 920 Compact Wheel Loader features a C3.6 engine, the Cat Optimized Z-bar Loader linkage, various work tools, a state-of-the-art electro-hydraulic system, a tuned drivetrain, a cab with all-around visibility, extended service intervals and excellent service access, and standard fuel savings features.
Rated Net Power - Rated Engine Speed | 2200 r/min |
Maximum Gross Power - Rated Engine Speed | 2200 r/min |
Rated Net Power - SAE J1349 | 120 HP |
Maximum Gross Power - ISO 14396 (metric) | 122 HP |
Rated Net Power - ISO 9249 | 118 HP |
Maximum Gross Torque - SAE J1995 | 372 ft·lbf |
Maximum Gross Torque - ISO 14396 | 369 ft·lbf |
Maximum Net Torque - SAE J1349 | 366 ft·lbf |
Maximum Net Torque - ISO 9249 | 363 ft·lbf |
Displacement | 220 in³ |
Bore | 3.85 in |
Stroke | 4.72 in |
Engine Model | Cat C3.6 |
Emissions | Engine meets Tier 4 Final/Stage V emission standards. |
Note | Net power advertised is the power available at the flywheel plus front drive implement pump when the engine is equipped with fan, air cleaner, muffler and alternator. |
Maximum Gross Power - ISO 14396 | 121 HP |
Maximum Gross Power | 121 HP |
Bucket Capacities - General Purpose | 1.3-1.9 m³ (1.7-2.5 yd³) |
Bucket Capacities - Light Material | 2.5-3.5 m³ (3.3-4.6 yd³) |
Bucket Capacities | 1.3-1.9 m3 (1.7-2.5 yd3) |
Operating Weight | 21742 lb |
Maximum Working Pressure - Steering Pump | 3190 psi |
Steering Cycle Times - Full Left to Full Right - At 2,350 rpm: 90 rpm Steering Wheel Speed | 2.3 s |
Steering Articulation Angle - Each Direction | 40 ° |
Number of Steering Wheel Turns - Full Left to Full Right or Full Right to Full Left | 3.4 turns |
Maximum Flow - Steering Pump | 21.7 gal/min |
Relief Pressure - Tilt Cylinder | 4641 psi |
Maximum Flow - Implement Pump - 3rd Function, Maximum Flow, Standard | 25 gal/min |
Maximum Flow - Implement Pump | 43.6 gal/min |
Relief Pressure - Tilt Cylinder - 4th Function Relief Pressure | 4641 psi |
Hydraulic Cycle Time - Float Down, Maximum Lift to Ground Level | 2.7 s |
Note | All cycle times listed are with cylinder snubbing turned off. |
Maximum Working Pressure - Implement Pump | 4061 psi |
Hydraulic Cycle Time - Total Cycle Time | 11.5 s |
Hydraulic Cycle Time - Rackback | 2.2 s |
Maximum Flow - Implement Pump - 4rd Function, Maximum Flow | 25 gal/min |
Hydraulic Cycle Time - Dump, at Maximum Reach | 1.8 s |
Hydraulic Cycle Time - Raise, Ground Level to Maximum Lift | 4.8 s |
Maximum Flow - Implement Pump - 3rd Function, Maximum Flow, High | 40 gal/min |
Transmission | 0.8 gal (US) |
Engine Crankcase | 2.6 gal (US) |
Diesel Exhaust Fluid (DEF) Tank | 4.8 gal (US) |
Axles - Rear | 4.5 gal (US) |
Cooling System | 5.7 gal (US) |
Hydraulic System - Including Tank | 25.9 gal (US) |
Axles - Front | 4.5 gal (US) |
Fuel Tank | 43.6 gal (US) |
Hydraulic Tank | 14.5 gal (US) |
Note | DEF used in Cat Selective Catalyst Reduction (SCR) systems must meet the requirements outlined in the International Organization for Standardization (ISO) standard 22241-1. |
Note | *Creeper Control allows speed control from a stand still up to 10 km/h (6.3 mph). The Creeper Control will only work in Range 1. |
Forward and Reverse - Speed Range 3 | 25 mile/h |
Forward and Reverse - Speed Range 2* | 12.5 mile/h |
Forward and Reverse - Speed Range 1* | 6.3 mile/h |
Rear | Oscillating ±11 degrees; Locking differential (standard) |
Front | Fixed; Locking differential (standard) |
ROPS | ISO 3471:2008 |
FOPS | EN ISO 3449:2008 (ISO 3449:2005) |
Note (3) | The labelled sound power level for the CE marked configurations when measured according to the test procedure and conditions specified in 2000/14/EC (as amended by 2005/88/EC) is 103 dB(A). |
Note (2) | The declared dynamic operator sound pressure levels per ISO 6396:2008*, when the cab is properly installed and maintained, is 77 dB(A). |
Note (1) | Cab and Rollover Protective Structures (ROPS) are standard in North America and Europe. |
Note (4) | *The measurements were conducted with the cab doors and windows closed. |
Other Choices Include | 17.5 R25 L3 XHA2; 20.5 R25 L3 XHA3; 17.5-25 L2/L3 SGL; 20.5-25 L2/L3 SGL; 17.5-25 L3 HRL D/L-3A; 17.5 R25 L2 Snow; 20.5 R25 L2 Snow; 17.5 R25 Solid |
Standard Size | 17.5 R25 L2 XTLA |
Note (1) | Other tire choices are available. Contact your Cat dealer for details. |
Note (3) | Caterpillar recommends that you consult a tire supplier to evaluate all conditions before selecting a tire model. |
Note (2) | In certain applications, the loader’s productive capabilities may exceed the tire’s tonnes-km/h (ton-mph) capabilities. |