C175-16 Generator Set

Minimum Rating	2500 kVA
Maximum Rating	3100 kVA
Emissions/Fuel Strategy	Low Fuel, Low Emissions
Voltage	380 to 11000 Volts
Frequency	50 Hz
Speed	1500 rpm
Duty Cycle	Standby, Mission Critical, Prime, Continuous

Engine Model	C175-16 SCAC, V-16, 4-Stroke Water-Cooled Diesel
Bore	6.89 in
Stroke	8.66 in
Displacement	5166.88 in³
Compression Ratio	16:07:01
Aspiration	Turbo Aftercooled
Fuel System	Common Rail
Governor Type	ADEM™ A4

Length - Minimum	241.6 in
Length - Maximum	311 in
Width - Minimum	83 in
Width - Maximum	108.5 in
Height - Minimum	87 in
Height - Maximum	130.2 in
Dry Weight - Genset (minimum)	42750 lb
Dry Weight - Genset (maximum)	50750 lb

Air Inlet System

4 x Single element canister with service indicator(s)

Control Panel

EMCP 4.2B
Volts (L-L & L-N)
Engine cycle crank
Power Factor (per phase & average)
Overcurrent
Communications
Emergency stop
2 Programmable relay outputs (Form C)
6 Programmable digital inputs
2 Programmable digital outputs
Environmental sealed front face.
DC Volts
Reverse power
Programmable Protective Relaying Functions
High coolant temperature
Accessory module data link
Low coolant level
Over / under frequency
Amps (per phase & average)
True RMS AC metering, 3-phase, +/-2% accuracy
Low coolant temperature
Reverse Reactive Power
Controls
Oil pressure (psi, kPa or bar)
Lamp test
Coolant temperature
Warning / shutdown Indicators
4 Programmable relay outputs (Form A)
Alarm acknowledge
Generator phase sequence
24 Volt DC operation
Serial annunciator module data link
Customer data link (Modbus RTU)
Failure to start (overcrank)
Auto / start / stop control.
Low oil pressure
RPM
Text alarm / event descriptions.
Digital Indicators
Generator mounted - rear facing
Emergency stop pushbutton
Engine cool-down timer.
Operating hours
Over / under voltage
Overspeed
Frequency (Hz)

Cooling System

Radiator group - shipped loose
SCAC cooling
Coolant Sensors
Coolant drain line and valves
Fan and belt guards

Exhaust System

Bolted flange, with bellow for each turbo
Dry Exhaust Manifold

Fuel System

Filters x 3
Secondary / Tertiary fuel filters
10 Micron Spin On Type
4 Micron Spin On Type
Primary fuel filter water / fuel water separator
Engine mounted filters X3

Generator and Attachments

6 Leads
IEC platinum stator RTDs
Voltage regulator
Reactive droop capability
3 Phase voltage sensing
RFI suppression
Min / max exciter limiter
exciter diode monitor
Form Wound
Permanent magnet
NEMA Class H insulation
Class H temperature rise at 40C ambient
(LV) Busbar connections, top/center mounted, top cable entry
3 Phase Brushless
Salient pole
50 Hz models: IEC standard hole pattern
(MV) Busbar connections, right side extension box, bottom cable entry
Anti condensation space heater
Class F temperature rise at 40C ambient
Right side extension box, bottom cable entry

Governing System

ADEM A4
Redundant shutdown (Overspeed protection through a duplicate speed sensing system)

Lube System

Gear type lube oil pump
Lubricating oil
Fumes disposal
Integral lube oil cooler
Oil drain lines and valve
Oil filter, filler and dipstick
Prelube - required with prime, continuous, and standby

Mounting Systems

Rubber anti-vibration mounts (shipped loose)
Battery disconnect switch
Batteries and battery rack w/cables
Dual 24 volt electric starting motors
Rails - Engine / generator

Service Instructions

Two PM inspections

Power Termination

Busbar

General

Paint - Caterpillar yellow with high gloss black rails & radiator
Right hand service
Flywheel and flywheel housing-SAE No. 00
SAE standard rotation

Air Inlet System

Single element air cleaner
Dual element air cleaner
Air inlet adapters
Air inlet protection

Control Panel

EMCP 4.3, EMCP 4.4
EMCP 4.4 optional harness
EMCP and MV&HV power connection locations
Load share module
EMCP mounting location - LV / MV
Customer AC-DC connection mounting location - LV/MV
Load share module / auxiliary plate and auxiliary box (LV)
Load share governor
Frame boxes
Automatically selected ground
EMCP voltage and current sensing groups
Raise lower switch
Speed adjust
Annunciator modules
Customer interface options
Generator temperature monitoring
Modbus monitoring of packages
E-Stop
Interconnect harness
Generator Harness

Cooling System

Package mounted radiator
Remote radiators
Fuel cooler

Exhaust System

Front housing - Standby or mission critical
Front housing - Prime or continuous
Exhaust collectors / Manifold
Exhaust support group
Mufflers
Weld flanges
Aftercooler drain

Crankcase Systems

Explosive relief valves
Crankcase ventilation system

Fuel System

Primary fuel filter

Generators and Attachments

Low voltage - 1800 and 3000 Frames - 50 Hz, 3 phase, 1500 rpm, FW, PM, No of leads=6, Pitch 0.6667
Medium Voltage - 1800 and 3000 Frames - 50 Hz, 3 phase, 1500 rpm, FW, PM, No of leads=6, Pitch 0.6667
Low Voltage - 1800 and 3000 Frames - 60 Hz, 3 phase, 1800 rpm, FW, PM, No of leads=6, Pitch 0.6667
Space heater kit
Thermostat for space heater
Conversion GP-Top cable entry
Generator air intake
Differential current transformers

Instrumentation

Pyrometer and thermocouples

Lube System

Lube oil heater
Drain group oil pans
Lubricating oil
Electric prelube pumps
Oil filters

Mounting

Rubber anti-vibration mounts
Spring type linear vibration isolators
IBC vibration isolators - Shipped loose

Power Connections

Center post busbars (LV)
Side / Rear mounted busbars (LV)
Harnesses (Breaker)
Cable entry options (LV)
Enclosures - Control packaging (LV)
Power connection covers (LV)
Neutral ground (LV)
1800 Frame generators circuit breaker
Masterpack breakers
Paralleling circuit breakers
1800 Frame generator side / rear mounted busbars (MV)
Cable entry options (MV)
Neutral ground (MV)
Low voltage connection cable
Masterpack breaker connections

Special Tests / Reports

Generator test report
PGS test report @ 1.0 power factor
PGS test report @ 0.8 power factor
Standard genset TVA (Torsional Vibration Analysis) report
Custom genset TVA report
Special test charge - Engine only
Genset fuel consumption test
Standard engine test charge
IBC seismic certification
OSCOSH1 seismic certification

Starting / Charging System

24 Volt power distribution box
24 Volt electric starting motors
Air starting motor
Air pressure regulator
Starter location covers
24 Volt battery sets - Dry
Heavy duty battery sets with rack
20 Amp battery chargers
35 Amp battery chargers
50 Amp battery chargers
Charging alternators - Dry
Jacket water heaters
Jacket water heater wiring groups

General

Special paint colors
Service tools - Engine barring group
Barring group manual
Engine barring air powered
Control GP - Air powered bar group

Generator Set Specifications

Engine Specifications

Generator Set Dimensions

Air Inlet System

Control Panel

Cooling System

Exhaust System

Fuel System

Generator and Attachments

Governing System

Lube System

Mounting Systems

Service Instructions

Power Termination

General

Air Inlet System

Control Panel

Cooling System

Exhaust System

Crankcase Systems

Fuel System

Generators and Attachments

Instrumentation

Lube System

Mounting

Power Connections

Special Tests / Reports

Starting / Charging System

General