C11 ACERT™ Dry Manifold Engine

C11 ACERT™ Dry Manifold Engine

Cat C11 ACERT engines are the ideal solution for your demanding operations in the oilfield. Decades of field operation and intense research and development allow Cat C11 ACERT engines to deliver excellent performance with low operating costs and emissions. Equipment powered by C11 ACERT engines include workover rigs, pump skids, acidizing units, cementing units, and hydraulic power units. Cat engines are backed by the worldwide network of Cat dealers ready to support your operation with technical support, service, parts, and warranty. C11 ACERT engines, with ratings: 242-336 bkW (325-450 bhp) @ 1800-2100 rpm, meet China Stage II, EPA Tier 3 equivalent, EU Stage IIIA equivalent emission standards. They are available using U.S. EPA and EU Flexibility, and for other regulated and non-regulated areas.

Download Product Brochure

General Specifications

Minimum Rating
325.0bhp
Maximum Rating
450.0bhp
Governor and Protection
Electronic (ADEM™ A3)
Aspiration
Turbocharged-Aftercooled
Displacement
681.0in3
Flywheel and Flywheel Housing
SAE 1 or SAE 2
Flywheel Teeth
113 (SAE 1), 138 (SAE 2)
Rotation (from flywheel end)
Counterclockwise
Stroke
5.51in.
Bore
5.12in

Emissions

Emissions
EPA and CARB Non-Road Mobile Tier 3, EU Stage IIIA

Dimensions

Length
47.3in.
Width
41.6in.
Height
46.3in.
Weight
1967.0lb

Capacity for Liquids

Lube Oil System (refill)
9.0gal

Standard Equipment

  • Air Inlet System
    • Turbocharger, mid-mounted
    • Air inlet elbow 90°, 104.5 mm (4.11" OD) hose connection
  • Control System
    • Electronic governing, PTO speed control
    • Programmable ratings
    • Cold mode start strategy
    • Automatic altitude compensation
    • Power compensation for fuel temperature
    • Programmable low and high idle and TEL
    • Electronic diagnostics and fault logging
    • Engine monitoring system — speed, temperature, pressure
    • J1939 Broadcast — diagnostic and engine status
  • Cooling System
    • Thermostats and housing
    • Jacket water pump — gear-driven
    • Front water pump inlet
  • Exhaust System
    • Exhaust manifold — dry
    • Front turbo exhaust
  • Flywheels And Flywheel Housings
    • See Mandatory Options
  • Fuel System
    • Electronic unit injector
    • Fuel filter — secondary, mid-mount, (LH 2 micron high performance)
    • Fuel transfer pump — front
    • Fuel priming pump — LH mid-mount
  • Lube System
    • Crankcase breather
    • Oil cooler
    • Oil filter — RH
    • Oil pan — front sump, 40 L capacity
    • Oil filler — LH front
    • Oil dipstick — LH mid-mount
    • Oil pump
    • Oil valve sampling — on oil filter base
  • Power Take-offs
    • Crankshaft pulley and damper — 250 mm (9.84 in), 2 grooves 22.3 mm (.87 in) width
    • Hydraulic pump drive — SAE A, 11 tooth
    • 1.41:1 drive ratio — counterclockwise rotation (45 lb-ft capacity)
  • General
    • Vibration damper
    • Paint — Cat yellow
    • Lifting eyes
    • Automatic variable timing, electronic
    • Electronic installation kit (connectors, pins, sockets)
    • Literature
  • Mandatory Options
    • Flywheel housing or rear PTO
    • Throttle position sensor
    • Primary filter/water separator

Optional Equipment

  • Air Compressor
    • Expansion chamber
    • Governors
    • Fittings
  • Air Inlet System
    • Air cleaners
    • Precleaners
    • Turbo air inlet
    • Air lines
  • Belt-driven Accessories
    • Refrigerant compressor and mounting
  • Charging System
    • Charging alternators
    • Alternator mountings
    • Alternator guard
    • Alternator accessories
  • Control System
    • Connection
  • Cooling System
    • Radiator — installed
    • Fan drive f/u/w Caterpillar installed radiator
    • Fan drive pulleys f/u/w customer-supplied radiators
    • Coolant conditioner
    • Water lines — pump inlet
    • Fan drive mountings
    • Fan height instructions
    • Fan adapters for suction fans
    • Fan adapters for blower fans
    • Suction fans
    • Blower fans
    • Coolant level sensor
    • Aftercooler lines
  • Exhaust System
    • Muffler
    • Flexible fitting
    • Elbows
    • Straight exhaust adapter
    • Flange
    • Pipe
    • Rain cap
    • Clamp
  • Fuel System
    • Fuel lines
    • Fuel cooler
    • Fuel fitting — fuel return and supply connections
    • Flexible fuel lines
  • Instrumentation
    • Gauges and instrument panels
    • Voltmeters
    • Gauge mounting
    • Ammeter
  • Lube System
    • Oil pan
    • Oil pan drain
    • Oil level gauges
    • Oil filter — bypass
    • Oil filter — remote
    • Lubricating oil
    • Oil filler
    • Fumes disposal
  • Mounting System
    • Front and rear engine supports
    • Structural steel base
  • Power Take-offs
    • Crankshaft pulleys
    • Crankshaft pulley — stack-on
    • Output flange
    • Flywheel stub shaft
    • Front stub shaft
    • Hydraulic pump drive
    • Hydraulic pumps — front
    • Hydraulic pumps — rear
    • Enclosed Clutch
    • Clutch Support
  • Protection System
    • Air shutoff
    • Air shutoff switch
  • Starting System
    • Electric starting motors — 12 Volt, 24 Volt
    • Starting aids
    • Battery sets — 24 Volt, dry
    • Battery cable
    • Battery rack
  • Transmission Arrangement
    • Transmission cooler